PIC18F4620-I/ML【PDF 284/286 页】IC MCU FLASH 32KX16 44QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3818

280页 281页 282页 283页 [284页]285页 286页

1996 Microchip Technology Inc.

DS30412C-page 97

PIC17C4X

13.4

USART Synchronous Slave Mode

The synchronous slave mode differs from the master

mode in the fact that the shift clock is supplied exter-

nally at the RA5/TX/CK pin (instead of being supplied

internally in the master mode). This allows the device

to transfer or receive data in the SLEEP mode. The

slave

mode

entered

clearing

the

CSRC (TXSTA<7>) bit.

13.4.1

USART SYNCHRONOUS SLAVE

TRANSMIT

The operation of the sync master and slave modes are

identical except in the case of the SLEEP mode.

If two words are written to TXREG and then the SLEEP

instruction executes, the following will occur. The rst

word will immediately transfer to the TSR and will trans-

mit as the shift clock is supplied. The second word will

remain in TXREG. TXIF will not be set. When the rst

word has been shifted out of TSR, TXREG will transfer

the second word to the TSR and the TXIF ag will now

be set. If TXIE is enabled, the interrupt will wake the

chip from SLEEP and if the global interrupt is enabled,

then the program will branch to interrupt vector

(0020h).

Steps to follow when setting up a Synchronous Slave

Transmission:

Enable the synchronous slave serial port by set-

ting the SYNC and SPEN bits and clearing the

CSRC bit.

Clear the CREN bit.

If interrupts are desired, then set the TXIE bit.

If 9-bit transmission is desired, then set the TX9

bit.

Start transmission by loading data to TXREG.

If 9-bit transmission is selected, the ninth bit

should be loaded in TX9D.

Enable the transmission by setting TXEN.

Writing the transmit data to the TXREG, then enabling

the transmit (setting TXEN) allows transmission to start

sooner then doing these two events in the reverse

order.

Note:

To terminate a transmission, either clear

the SPEN bit, or the TXEN bit. This will

reset the transmit logic, so that it will be in

the

proper

state

when

transmit

re-enabled.

13.4.2

USART SYNCHRONOUS SLAVE

RECEPTION

Operation of the synchronous master and slave modes

are identical except in the case of the SLEEP mode.

Also, SREN is a don't care in slave mode.

If receive is enabled (CREN) prior to the SLEEP instruc-

tion, then a word may be received during SLEEP. On

completely receiving the word, the RSR will transfer the

data to RCREG (setting RCIF) and if the RCIE bit is set,

the interrupt generated will wake the chip from SLEEP.

If the global interrupt is enabled, the program will

branch to the interrupt vector (0020h).

Steps to follow when setting up a Synchronous Slave

Reception:

Enable the synchronous master serial port by

setting the SYNC and SPEN bits and clearing

the CSRC bit.

If interrupts are desired, then set the RCIE bit.

If 9-bit reception is desired, then set the RX9 bit.

To enable reception, set the CREN bit.

The RCIF bit will be set when reception is com-

plete and an interrupt will be generated if the

RCIE bit was set.

Read RCSTA to get the ninth bit (if enabled) and

determine if any error occurred during reception.

Read the 8-bit received data by reading

RCREG.

If any error occurred, clear the error by clearing

the CREN bit.

Note:

To abort reception, either clear the SPEN

bit, the SREN bit (when in single receive

mode), or the CREN bit (when in continu-

ous receive mode). This will reset the

receive logic, so that it will be in the proper

state when receive is re-enabled.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式